FC280 Programming Guide MG07C202.pdf

(9593 KB) Pobierz
Programming Guide
®
Midi Drive FC 280
VLT
vlt-drives.danfoss.com
Contents
Programming Guide
Contents
1 Introduction
1.1 How to Read This Programming Guide
1.2 Definitions
1.2.1 Frequency Converter
1.2.2 Input
1.2.3 Motor
1.2.4 References
3
3
4
4
4
4
5
7
10
10
10
10
12
12
20
23
23
31
41
43
49
52
62
66
71
75
75
75
76
82
88
90
94
95
96
98
98
1
1.3 Electrical Wiring - Control Cables
2 Safety
2.1 Safety Symbols
2.2 Qualified Personnel
2.3 Safety Precautions
3 Programming
3.1 Local Control Panel Operation
3.2 Basic Programming
4 Parameter Descriptions
4.1 Parameters: 0-** Operation and Display
4.2 Parameters: 1-** Load and Motor
4.3 Parameters: 2-** Brakes
4.4 Parameters: 3-** Reference/Ramps
4.5 Parameters: 4-** Limits/Warnings
4.6 Parameters: 5-** Digital In/Out
4.7 Parameters: 6-** Analog In/Out
4.8 Parameters: 7-** Controllers
4.9 Parameters: 8-** Communications and Options
4.10 Parameters: 9-** PROFIdrive
4.11 Parameters: 10-** CAN Fieldbus
4.12 Parameters: 12-** Ethernet
4.13 Parameters: 13-** Smart Logic Control
4.14 Parameters: 14-** Special Functions
4.15 Parameters: 15-** Drive Information
4.16 Parameters: 16-** Data Readouts
4.17 Parameters: 18-** Data Readouts 2
4.18 Parameters: 21-** Ext. Closed Loop
4.19 Parameters: 22-** Application Functions
4.20 Parameters: 30-** Special Features
4.21 Parameters: 32-** Motion Control Basic Settings
MG07C202
Danfoss A/S © 03/2016 All rights reserved.
Contents
VLT
®
Midi Drive FC 280
4.22 Parameters: 33-** Motion Control Adv. Settings
4.23 Parameters: 34-** Motion Control Data Readouts
4.24 Parameters: 37-** Application Settings
99
100
101
103
103
106
123
123
131
5 Parameter Lists
5.1 Introduction
5.2 Parameter Lists
6 Troubleshooting
6.1 Warnings and Alarms
Index
2
Danfoss A/S © 03/2016 All rights reserved.
MG07C202
Introduction
Programming Guide
1 Introduction
1.1 How to Read This Programming Guide
1.1.1 Purpose of the Manual
This programming guide provides information about
controlling the frequency converter, accessing parameters,
programming, and troubleshooting.
The programming guide is intended for use by qualified
personnel who are familiar with the VLT
®
Midi Drive FC
280 frequency converter.
Read the instructions before programming and follow the
procedures in this manual.
VLT
®
is a registered trademark.
AC
AEO
ACP
AWG
AMA
°C
DC
EEPROM
EMC
EMI
ETR
f
M,N
FC
IP
I
LIM
I
INV
I
M,N
I
VLT,MAX
I
VLT,N
L
d
L
q
LCP
MCP
N.A.
P
M,N
PCB
PE
PELV
PWM
R
s
Regen
RPM
RFI
SCR
SMPS
T
LIM
U
M,N
X
h
Table 1.2 Abbreviations
Alternating current
Automatic energy optimization
Application control processor
American wire gauge
Automatic motor adaptation
Degrees Celsius
Direct current
Electrically erasable programmable
read-only memory
Electromagnetic compatibility
Electromagnetic interference
Electronic thermal relay
Nominal motor frequency
Frequency converter
Ingress protection
Current limit
Rated inverter output current
Nominal motor current
Maximum output current
Rated output current supplied by the
frequency converter
Motor d-axis inductance
Motor q-axis inductance
Local control panel
Motor control processor
Not applicable
Nominal motor power
Printed circuit board
Protective earth
Protective extra low voltage
Pulse width modulated
Stator resistance
Regenerative terminals
Revolutions per minute
Radio frequency interference
Silicon controlled rectifier
Switch mode power supply
Torque limit
Nominal motor voltage
Motor main reactance
1
1
1.1.2 Additional Resources
Additional resources include:
•
VLT
®
Midi Drive FC 280 Operating Guide,
provides
the necessary information for getting the
frequency converter up and running.
•
VLT
®
Midi Drive FC 280 Design Guide,
provides
detailed technical information about the
frequency converter, customer design, and
applications.
VLT
®
Midi Drive FC 280 Service Guide,
provides
information to Danfoss authorized, qualified
technicians on how to service the FC 280
frequency converters.
•
Contact the local Danfoss supplier or go to
drives.danfoss.com/knowledge-center/technical-documen-
tation/
to download the documentations.
1.1.3 Document and Software Version
This manual is regularly reviewed and updated. All
suggestions for improvement are welcome.
Table 1.1
shows
the document version and the corresponding software
version.
Edition
MG07C2
Remarks
Update due to new software
version release.
Table 1.1 Document and Software Version
Software
version
1.1
MG07C202
Danfoss A/S © 03/2016 All rights reserved.
3

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin