Fokker DR1 Plans (Parts Templates Non-Tiled).pdf

(69 KB) Pobierz
Copyright © 2005
Designed by Steve Shumate
Upper wing
(Make 1)
0.188" dia x 31.5"
carbon tube spar
All Rights Reserved
Cut slot to
fit wing struts
Cut slot to
fit wing struts
All parts are made from 6 mm Depron or
BlueCore foam unless otherwise specified
If you enjoy these plans, please consider sending a small contribution
to the designer to show your appreciation for the work that went into
them. Suggested contribution is $5 to $10 U.S., and can be sent
via PayPal to jetset44@verizon.net. Thanks for your support!
Main wing struts
(Make 2 from 1/8" lite-ply)
Middle wing
(Make 1)
1.0"
0.157" dia x 27.2"
carbon tube spar
Cut slot to
fit wing struts
Cut slot to
fit wing struts
Elevator control horns
(Make 1 from 1/32" ply)
Aileron control horns
(Make 2 from 1/32" ply)
La
(Mak nding ge
a
e 2 fr
om 1 r struts
/8" lit
e ply
)
1/4" square hardwood joiner
(bevel 45 degrees on leading edge)
Rudder control horn
(for pull-pull threads)
(Make 1 from 1/32" ply)
Aileron connectors
(Make 6 from 1/32" ply)
Horizontal tail
(Make 1)
Lower wing
(Make 1)
0.188" dia x 28.5"
carbon tube spar
Cut slot to
fit wing struts
Cut slot to
fit wing struts
Vertical tail
(Make 1)
Cut access hatch
for receiver
Tail skid support
(Make 1)
Tail skid
(Make 1 from
1/8" lite-ply)
Front of cowling
(Make one from 3mm Depron)
Fwd wing strut doubler
Aft wing strut doubler
F-3
Fuselage sides
(Make 2)
Bevel top edge of aft fuselage to
match curvature of turtledeck top
Exit hole for elevator pushrod
(right side only)
Exit holes for rudder threads
(both sides)
F-1
Fwd lan
ding ge
ar
strut do
ubler
F-2
Aft landing gear
strut doubler
Servo tray location
F-4
Wing alignment marks
Aft fuselage bottom
(Make 1 from 3mm Depron)
Fwd fuse top
(Make 2 and laminate)
Base cross piece for
all alignment guages
(Make 2)
ts
stru e ply)
ing
lit
ter w 1/8"
Cen from
ke 2
(Ma
Uppe
r win
g alig
(Mak nment gu
e 2)
age
2nd layer of cowling
(Make 1)
Inner layers of cowling
(Make 7)
GWS Pico
servos
shown
Top overwing fairing
(Make 1)
Cut cockpit hole
AFTER installing
turtledeck top
Turtledeck top
(Make 1 from 3mm Depron)
Center wing strut angle guage
(Make 2)
Motor stick support
(Make 2)
Landing gear wing
(Make 2, laminate,
and sand to airfoil shape)
Cut slot for 0.125" dia x 8.75"
carbon tube axle
Servo tray
(Make 2 and
laminate)
Turtledeck/
stabilizer
trim piece
(Make 1 from
3mm Depron)
Motor stick side supports/
battery tray
(Make 2)
F-1
Motor stick
support
Side support/
battery tray
F-2
Motor stick
support
Side support/
battery tray
Hole for elevator pushrod
Aft landing gear/
aft wing strut doubler
(Make 4)
Wheels used on
prototype (for 3.0" O.D.
O-rings) (Make 2)
Slot for rudder threads
Wheel hubs
(Make 2 each
from 1/32" ply)
Inboard
Outboard
Optional scale wheels
(for 3.5" O.D. O-rings)
(Make 2)
Cut hole for
motor wires
Cut
lightening
hole
9/16" dia.
3/4" dia.
Drill all wheel hubs for
1/8" dia. carbon tube axle
F-3
2.75" dia.
Wheel axle stop
(Make 2 from
1/8" lite-ply)
9/16" dia.
3.25" dia.
Fwd fuselage bottom
(Make 1)
Landing gear strut angle guage
(Make 1)
d shape to
Sand sides to rounde
ge curvature
match upper fusela
Cut hatch to access battery
after installation
Cut two holes for
battery cooling
Cut two holes for
battery cooling and
wiring access
F-4
Fwd wing strut doubler
(Make 2)
Fwd landing gear
strut doubler
(Make 2)

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin