X 5 2001 petrol NO.pdf

(18 KB) Pobierz
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS
www.cobra.it
REV. 00
PETROL
DIESEL
X
MAKE
ALARM/SIREN
POSITION
CENTRAL POSITION
POWER SUPPLY
BMW
MOD.
X5
YEAR
01
→
Position the compact alarms and the sirens on the passenger’s side wheelhouse.
Install the modular systems and the modules behind the glove box under the
dashboard, passenger’s side.
+ 30:
connect to the 6 mm
2
RED wire located in the wiring harness along the steering
column.
- 31:
connect to a ground terminal located behind the left lateral bulkhead, driver’s
side.
+15/54:
connect to the wire with the function of ignition wire located in the wiring
harness coming out of the connector of the ignition key.
Connect to the wires: BLUE/GREEN at the position nr.11 (ant.left), BLUE/BROWN at
the position nr.12 (post.right), BLUE/YELLOW at the position nr.14 (lat.left) located in
the wiring harness of the 15 way white connector; BLUE/GREEN at the position nr.8
(post.left), BLUE/BROWN at the position nr.6 (ant. right), BLUE/YELLOW at the
position nr.14 (lat. right) located in the wiring harness coming out of the 15 way black
connector located on the coming out of the lights module, on the right of the
passenger’s side glove compartment, behind the covering.
Refer to the
diagram nr.147.
Comfort closing
Negative control signal
The total closing of the windows is obtained timing at 24s. the LIGHT BLUE/RED wire,
position nr.4, the same wire used for the doors locking.
Negative control signal
Connect to the LIGHT BLUE/RED wire at the position nr. 4 (lock) and to the
WHITE/BLACK wire at the position nr. 3 (unlock) located in the wiring harness coming
out of the 12 way black connector directly in the buttons panel inside the driver’s side
door.
Fuel pump
Cut the 0,5 mm
2
BLACK/VIOLET wire located in the wiring harness coming out of the
connector marked CG, in the connectors holder rod placed in the fuse box under the
passenger’s side dashboard.
+50:
cut the wire located at the position “+50” in the wiring harness coming out of the
ignition key.
Install an additional switch on the front headlamp support plate, passenger’s side.
Connect to the RED/BLUE wire, at the position nr. 20, located in the wiring harness
coming out of the 20 way black connector on the coming out of the central locking unit
placed behind the glove compartment, passenger’s side. Invert the signal with a
supplementary relay.
Attention:
as the polarity of the doors is at a positive control signal, it is necessary to
invert the signal by using a relay.
IGNITION WIRE
DIRECTION INDICATORS
ELECTRIC WINDOWS
CENTRAL DOORS LOCKING
IMMOBILISATION POINT
STARTER
BONNET SWITCH
DOORS AND BOOT
SWITCHES
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
bmx501gbb.doc
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS
www.cobra.it
REV. 00
FITTING DIAGRAM N°147
Diagram for direction indicators connection for
BMW X5
YELLOW
YELLOW
15 way
white connector
BLUE/GREEN
Pos. nr.11
BLUE/BROWN
Pos. nr.12
BLUE/YELLOW
Pos. nr.14
BLUE/GREEN
Pos. nr. 8
BLUE/BROWN
Pos. nr. 6
BLUE/YELLOW
Pos. nr.14
15 way
black connector
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
bmx501gbb.doc

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin