MZD CONNECT REVISED for EU N Firmware ONLY.pdf

(1594 KB) Pobierz
Attachment for R036/18D
Page 1 of 9
New MARCH 2020 MZD Connect CMU Software Update Procedure
For
EU N
FIRMWARE USE
ONLY
or CARS STILL USING
EU N 56.00.100
or OLDER.
NOTE:
Most revisions are written in red texts.
Software update procedure: There are two versions: A) Full version and B) One Page version.
Both versions contain the instruction to avoid update failure.
The One Page version’s purpose is to print and use for update procedure in the vehicle.
NOTE:
If current software version is older than 56.00.100 like 33.00.100, 42.00.100 or 45, 52, 55.00.100
update first to 70.00.100,
then update
to the
352B
version.
IF car
is still on
Stage 1
Firmware like
25.00.100, 26, 27, 28, 30.00.200 then
MUST
INSTALL
31.00.100A BEFORE Stage 2 EU N 70.00.100.
A) Full version: (BEST
UPDATE PROCEDURE --- USE THIS FULL VERSION Only).
1. Remove Navigation SD card (if customer has one) and all other devices (USB, AUX, Mobile
phones. …) connected to the MZD Connect when ignition position is OFF.
2. Push engine start button once without depressing clutch pedal (manual transaxle) or brake pedal
(automatic transaxle). This will set ignition to ACC.
Wait until MZD system is booted.
3. Select AM, FM or DAB radio.
Attachment for R036/18D
Page 2 of 9
4. Press three buttons (Music (A) + Favorite (B) + Volume Mute(C)) on the commander switch at
the same time for 2-5 seconds and the Diagnostic Test Screen will appear.
5. Use the touchscreen or the commander knob to input ‘3’ on test screen and then select “ENTER”
and “CLEAR”.
6. Input ‘2’ on test screen and then select “ENTER”. (This will internally clear earlier set DTCs in
CMU). Select “CLEAR” and then “EXIT”.
7. Switch ignition OFF, close all doors (regardless bonnet), lock vehicle with remote, keep all
remote transmitters 5 m or more away from the vehicle, and wait for 3 minutes (CMU sleep
mode).
8. Unlock the vehicle and press the START/STOP ENGINE push button once
without
depressing
the clutch pedal (manual transaxle) or the brake pedal (automatic transaxle), to switch the
ignition position to ACC.
Attachment for R036/18D
Page 3 of 9
9. Connect the prepared USB memory stick to one of the two USB port (A) (depending on vehicle
equipment).
NOTE:
Only
stick should be
ports. Nothing
other USB port and SD slot during the re-flashing process.
the prepared USB memory
inserted in one of USB
should be inserted in the
10. When the USB memory stick is recognized, following message will appear briefly on the screen.
NOTE:
If USB memory stick is not recognized by the system, return to step 9.
11. Press again the three buttons (Music (A) + Favorites (B) + Volume Mute(C)) on commander
switch at the same time for 2-5 seconds.
12. Use touchscreen or commander knob to input ‘99’ and then select “ENTER” on Diagnostics Test
screen.
Attachment for R036/18D
Page 4 of 9
13. Select “Search” on screen below.
14. When updating to software version 70.00.335 or later, go to step 22.
(“Fail Safe Package” has been eliminated since 70.00.335. No need to perform Failsafe
installation process since then.)
[Only when updating to software version 31.00.100]
Select “Fail Safe Package” first.
CAUTION:
Always do the “Fail Safe Package” first.
Note:
Please check if CMU S/W is 29.00.000 or older. If yes, refer to Service Information
R036/18.
Note:
Please DO NOT switch ignition OFF or allow system to switch off ignition automatically until
all updates have been installed.
Note:
Stay inside the vehicle until failsafe package installation is finished.
15. Select “Install” on the screen below and the Failsafe installation process will start.
Attachment for R036/18D
Page 5 of 9
16. Failsafe installation process will start and will take several minutes.
17. After Failsafe installation process is completed, select “OK”
18. Press and release clutch pedal (Manual Transaxle) or brake pedal (Automatic Transaxle) and
proceed with following steps without stopping.
NOTE:
If the ignition is left in ACC position it will automatically switch off after 25 minutes.
Performing this step resets timer to ensure vehicle does not switch off while installing
reinstallation package.
19. Press the three buttons (Music (A) + Favorite (B) + Volume Mute(C)) on commander switch at
the same time for 2-5 seconds to open the Diagnostics Test screen again.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin