ENGINE SECTION.pdf

(17469 KB) Pobierz
SERVICE PROCEDURE
[W100]
FOREWORD
1. Important Safety Notice
1. Important Safety Notice
¼
Providing appropriate service and repair is a matter of great importance in the serviceman’s safety
maintenance and safe operation, function and performance which the SUBARU vehicle possesses.
¼
In case the replacement of parts or replenishment of consumables is required, genuine SUBARU parts
whose parts numbers are designated or their equivalents must be utilized.
¼
It must be made well known that the safety of the serviceman and the safe operation of the vehicle would
be jeopardized if he used any service parts, consumables, special tools and work procedure manuals which
are not approved or designated by SUBARU.
3
FOREWORD
[W200]
2. How to Use this Manual
SERVICE PROCEDURE
2. How to Use this Manual
¼
This Service Manual is divided into four volumes by section so that it can be used with ease at work.
Refer to the Table of Contents, select and use the necessary section.
¼
¼
¼
¼
GENERAL INFORMATION SECTION
REPAIR SECTION
DIAGNOSTICS SECTION
WIRING DIAGRAM SECTION
¼
Each chapter in the manual is basically made of the following four types of areas.
S
C
W
(X
(Y
K
SPECIFICATIONS AND SERVICE DATA
COMPONENT PARTS
SERVICE PROCEDURE
SERVICE PROCEDURE)
SERVICE PROCEDURE)
DIAGNOSTICS
¼
The description of each area is provided with four types of titles different in size as shown below. The
Title No. or Symbol prefixes each title in order that the construction of the article and the flow of explana-
tion can be easily understood.
[Example of each title]
¼
Area title:
¼
Large title (Heading):
¼
Medium title (Section):
¼
Small title (Sub-section):
W SERVICE PROCEDURE (one of the four types of areas)
1. Oil Pump (to denote the main item of explanation)
A: REMOVAL (to denote the type of work in principle)
1. INNER ROTATOR (to denote a derivative item of explanation)
4
SERVICE PROCEDURE
[W200]
FOREWORD
2. How to Use this Manual
¼
The Title Index No. is indicated on the top left (or right) side of the page as the book is opened. This is
useful for retrieving the necessary portion.
H0M0010
5
FOREWORD
[W200]
2. How to Use this Manual
SERVICE PROCEDURE
¼
In this manual, the following symbols are used.
*
5
Selective part
Replacement part
Should be lubricated with oil.
S0M0001
Should be lubricated with grease.
S0M0002
Sealing point
S0M0003
Tightening torque
S0M0004
¼
WARNING, CAUTION,
NOTE
¼
WARNING:
¼
CAUTION:
¼
NOTE:
Indicates the item which must be observed precisely during performance of maintenance services in
order to avoid injury to the mechanics and other persons.
Indicates the item which must be followed precisely during performance of maintenance services so as to
avoid damage and breakage to the vehicle and its parts and components.
Indicates the hints, knacks, etc. which make the maintenance job easier.
¼
SPECIAL TOOLS
When any special tool is required to perform the
job, it is identified by “ST” in the applicable illustra-
tion and its part number is shown in the manual.
H0M0011A
6
2-1
[W1A0]
1. Front Catalytic Converter
SERVICE PROCEDURE
5) Disconnect rear oxygen sensor connector.
(Except California spec. vehicles)
1. Front Catalytic Converter
A: REMOVAL
1) Disconnect battery ground cable.
B2M0312
G6M0095
6) Separate center exhaust pipe from front cata-
lytic converter.
2) Disconnect front oxygen sensor connector.
S2M0052
S2M0127
3) Disconnect rear oxygen sensor connector.
(California spec. vehicles)
7) Remove bolts which hold front exhaust pipe
onto cylinder heads.
CAUTION:
Be careful not to pull down front exhaust pipe
and center exhaust pipe.
S2M0128
4) Lift-up the vehicle.
S2M0236
2

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin